PDA

View Full Version : Need additional opinions


5MadFarmers
08-06-2013, 06:02
Two pictures. Please tell me if you think this is the work of Springfield Armory or not.

http://5madfarmers.com/96_bar/krag_barrel-1.JPG

http://5madfarmers.com/96_bar/krag_barrel-2.JPG
psteinmayer
08-06-2013, 06:27
It looks TIG welded to me... anyone else see that, or is it just me???
5MadFarmers
08-06-2013, 06:36
You're correct. Good. I wanted a second opinion as it was beginning to disturb me. That barrel is going on a mock gun but it's currently mounted on an interesting receiver.

I'll break the two up with no worries.

Thanks.
Dick Hosmer
08-06-2013, 06:53
+1 on NG.
5MadFarmers
08-06-2013, 07:05
Back story. That barrel is attached to receiver 24110. It's carbine length but flat crowned. I guess you'll understand my taking a real good look before breaking them apart.

The gun had the M-1896 "lugged" rifle sight, now have 3, installed backwards.

The receiver will, when seen, be a cadet.
The barrel will be, when seen, on the M-1892 carbine.

I don't know if I'll get either done in time and don't know, if I do, if I'll even use them. We'll see how they turn out.
jon_norstog
08-07-2013, 09:37
I don't think it's TIG, unless it was done by not particularly skilled micro-elves. My guess would be a lousy silver-braze job with too much flux. What you could call a cold joint. Try hitting the ramp with a copper hammer. I bet it comes right off.

jn
madsenshooter
08-07-2013, 09:41
Sounds like a couple fun projects.
5MadFarmers
08-07-2013, 10:25
Sounds like a couple fun projects.

That cadet stock Gunderson had would have been helpful. 21163 is a curved stock M-1892 not having been altered. I'm shipping that to a stock duplicator and having it duplicated - minus the swivel cut in the butt. I'll add the band spring channel and hole. Viola - Cadet stock. The only hard part is the cleaning rod. An aftermarket three section one, welded together by micro-elves, will have to suffice.

The M-1892 carbine project presents many more difficulties. That's ok, we'll see how it comes out. I have an M-1892 rifle, altered, which somebody sliced off the end of. Pity as it was a very nice rifle. That, with this barrel on it, will become the carbine. With the obvious alterations, patching the stock to remove the curved butt, filling in the butt swivel cut, fabricating the front band, etc., it'll never be pretty. The receiver notch will also be a bummer. So it'll be ugly. That's the way it goes. This barrel will fit right in. An M-1892 assembled by micro-elves and their wood shop.
madsenshooter
08-07-2013, 08:03
Micro-elves in the woodshop is ok, but never, ever, let them do the loading! I've tried to explain to them time and time again, but they just don't get it. I always have to work their loads down!
psteinmayer
08-08-2013, 07:06
So that was yer problem at Perry Bob? The Micro-Elves buggered up your ammo to the point that you smoked me in the Vintage? Stupid elves!!!
madsenshooter
08-09-2013, 10:00
If I'd used their loads I'd have been 3gr hotter, and I wouldn't have been able to lift the bolt after each shot. Stupid elves. Are they in some way related to gremlins? Only if you get em wet?
psteinmayer
08-09-2013, 10:59
LOL Too Funny.... Ok, now I gotta go hide the food because it's almost midnight!
seagoatami
08-09-2013, 12:21
I don't think it's TIG, unless it was done by not particularly skilled micro-elves. My guess would be a lousy silver-braze job with too much flux. What you could call a cold joint. Try hitting the ramp with a copper hammer. I bet it comes right off.

jn

I agree with you jon, also might add looks like the wrong grade of silver also, think that may be the reason for the way it looks