M1 bolt disassy

[PWC]

Is there a way to disassemble an M1 bolt without the 'tool'? I won't be doing it often enough to require the tool, but I do want to inspect the innards.

[gwp]

You can use an empty 45 ACP case on a sturdy flat surface to depress the ejector spring to remove the extractor.

[RCS]

The M10 tool on a short length of cleaning rod is very efficient. Just insert into the chamber on a complete rifle and turn
it slowly to left up the extractor which will release the parts. You can do this on just the upper part of the M1 without the
stock or trigger housing too. The operating rod spring provides the pressure - same thing for re-assembling the parts.

[PWC]

The question was "Is there a way to disassemble an M1 bolt without the 'tool'?"

Thank you GWP for your answer, I will look at that. Are their any other shortcuts?

[dryheat]

Take a fired 30-06 case and close the vise jaws over about 2" of the mouth so it's sturdy and pointing horizontal towards you. Press the bolt face(right side up) into the base until it's flush. Hold(I use right hand) and take flat blade screwdriver in left hand and START to remove the extractor. Once it's broken free remove pressure on the bolt and carefully continue to remove the extractor without letting things go flying.

I use the same procedure to assemble except then I use a medium pair of channel locks with protective electrical tape to "crunch" the extractor back in place.

[PWC]

Thank you dryheat; that seems like a common sense idea using the cartridge it is designed for.

When I cools down a bit more in the garage I'll do that. Do you shoot at BASF, PRG or RSSC, or BLM land?

[togor]

My cartridge case is stuck into a short length of 2x4 as opposed to a vise, but +1 to the general idea.

[Orlando]

Don't need anything more than your fingers and a punch
https://www.youtube.com/watch?v=FWhvvTm1cLk

[PWC]

Thanks guys; I like the idea of the cartridge case as a tool, and the video was great to, especially for some one that has never seen it done.

[CPC]

Just put your thumb over the end and push the extractor out with needle nose pliers. With a little practice you can assemble with a stubby wide flat tip screwdriver. Until you get the hang of it put the end in a gallon ziplock or other clear bag in case the spring flys. Just one of the many techniques used as highlighted previously

[Rick B]

I did this video some years ago. Hope it helps. Rick B

https://www.youtube.com/watch?v=qYM8JnI2CJg

[PWC]

Rick B - Thank you, I did find that on Youtube earlier; slickest and fastest method yet.

I think I'll combine your's with dryheat's use of a cartridge (as above) for reassy. I don't trust myself with the stubby screwdriver slipping off; the case head fills the 'hole'.

[mike9905]

PWC: Buy the tool. It is a really neat device. Of course you will need to buy more Garands to justify the purchase.

[Bill E]

Agree, tool is not that expensive and if one is going to disassemble bolts frequently it's worth having. The various suggestions were excellent though.

[PWC]

I've never taken the bolt apart before; I want go do a one time inspection then annualy thereafter. Cost of tool will be better applied to reloading accessories.

[Rock]

Which tool are you referring to? The Bolt disassembly tool or the M10 combination tool that is stored in the butt stock?

[PWC]

Either one. My M1 is a beater, a shooter...could be a ranch rifle, if I had a ranch. It is a shooter, I'm not interested in collecting. I have what's needed to clean the rifle.

The forward guard had a crack (can't see it now) that jas been armorer repaired with brass screws/pins cut flush. And the same type repair to the toe. I could have replaced the stock, but the repairs are a part of the character of the gun. Value is beyond $$, it is intrinsic to whichever grangson gets it.

[nf1e]

The tool for both M1 and M14 bolts is the way to go for ease of use. I have had a cartridge case drilled into the side of one of my benches for over 30 years for quick and easy disassembly/assembly. I just press the bolt , with the extractor base up, against the cartridge base to relieve pressure on the ejector spring and push the extractor out with a small punch. Just the opposite for installation.
These days I have been using the commercial tool so much that I almost forget what the cartridge sticking out the side of the bench is for. Memory is such a small thing.

http://i1180.photobucket.com/albums/x413/nf1e/IMG_2132_zps9egrlimu.jpg (http://s1180.photobucket.com/user/nf1e/media/IMG_2132_zps9egrlimu.jpg.html)

http://i1180.photobucket.com/albums/x413/nf1e/IMG_2134_zpsrkohnnhc.jpg (http://s1180.photobucket.com/user/nf1e/media/IMG_2134_zpsrkohnnhc.jpg.html)

http://i1180.photobucket.com/albums/x413/nf1e/IMG_2135_zpsmhrhctvd.jpg (http://s1180.photobucket.com/user/nf1e/media/IMG_2135_zpsmhrhctvd.jpg.html)

[tmark]

The first time I took my bolt apart, three parts flew off the bolt in three different directions onto my thick shag carpet living room rug. I was lucky to find all the parts. Since then, I disassemble the bolt in a clear plastic bag.

[Dan Shapiro]

three parts flew off the bolt

Buddy bought over his M1 carbine. Seems the extractor flew off while he was firing. He found the extractor, but not the plunger and spring. After getting the needed part, I was reassembling the bolt for him when the plunger took off, flying across the garage. Try finding a tiny part like that. As luck would have it, I did find it with the help of a broom and magnet. Weapon has now been successfully reassembled.

[M1Tommy]

I did this video some years ago. Hope it helps. Rick B

https://www.youtube.com/watch?v=qYM8JnI2CJg

Great vid. Rick B. Thanks for the link.

There, some more genius of Mr. Garand's design, IMO.
Tommy