Results 1 to 9 of 9
  1. #1
    Join Date
    Nov 2012
    Location
    Connecticut
    Posts
    1,958

    Default TRW/Bula/James River

    Pulling parts for a build to start next week.
    TRW heeled James River Armory/Bula receiver is on the way.
    Barrel is Kreiger Heavy SS 1-10.
    USGI flash suppressor.
    TRW bolt.
    TRW Op Rod
    TRW Trigger group.
    TRW Rear Sight.
    USGI unitized gas system.
    SADLAK spring guide.
    Nice Walnut stock with , of coarse, Hawk's kit installed.
    USGI hand guard.
    Sparrowhawk Ambi kit.

    Last edited by nf1e; 12-29-2019 at 04:46.

  2. #2
    Join Date
    Sep 2009
    Location
    Georgia
    Posts
    3,736

    Default

    Always a pleasure to follow post of you building rifles. sincerely. bruce.
    " Unlike most conservatives, libs have no problem exploiting dead children and dancing on their graves."

  3. #3
    Join Date
    Nov 2012
    Location
    Connecticut
    Posts
    1,958

    Default

    Quote Originally Posted by bruce View Post
    Always a pleasure to follow post of you building rifles. sincerely. bruce.
    Thanks Bruce. I am having way too much fun.

  4. #4
    Join Date
    Nov 2012
    Location
    Connecticut
    Posts
    1,958

    Default

    The brake is an LRB that affixes in place of a standard flashhider and uses the same front sight. They are very well made and I highly recommend them.
    Always keep a few in the shop for builds.


  5. #5
    Join Date
    Nov 2012
    Location
    Connecticut
    Posts
    1,958

    Default

    Scheduled to arrive tomorrow.


  6. #6
    Join Date
    Sep 2009
    Location
    London, Ontario
    Posts
    3,251

    Default

    TRW was the original maker, as I'm sure you know. In the spirit of 'Thou shalt CYA', and assuming it is a real TRW receiver, keep in mind your ATF was running around confiscating real M-14 receivers several years ago. Their unelected civil servant 'no legislation required' law by regulation of 'Once an MG always an MG' was invoked. No compensation for the confiscated receivers either.
    Spelling and grammar count!

  7. #7
    Join Date
    Nov 2012
    Location
    Connecticut
    Posts
    1,958

    Default

    The TRW marked receiver is another of the James River Armory/Bula receivers that have undergone the simple attachment of the heel only to a new Bula receiver.

    The windage marks on the TRW/Bula receiver are very light, but quite visible. If I were a better photographer perhaps they could show up better.



    At least the mfg shows up better than many I have seen.



    Fun projects at any rate.


  8. #8
    Join Date
    Nov 2012
    Location
    Connecticut
    Posts
    1,958

    Default

    All three pass the first test of bolt free travel.


  9. #9
    Join Date
    Nov 2012
    Location
    Connecticut
    Posts
    1,958

    Default

    It's a tough job but somebody has to do it. Took out the TRW with Heavy Kreiger SS 1-10 yesterday and ran 20 rnds through her at 100yds with LC 13 M80. Target shown is second target with 10 rnds. No change to sights after build other than 6 clicks of elevation. Hoping to get out today and make a couple of adjustments.

    TRW finished heel with USMC sight cover..jpgKreight barrel.jpgTRW stock cartouce.jpgTRW stock 98.jpgTRW with new Kreiger SS 1-10..jpg
    Last edited by nf1e; 12-29-2019 at 04:52.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •